===== 产品图 =====


{{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_20w/001.jpg?250x250}}
{{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_20w/002.jpg?250x250}}
{{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_20w/003.jpg?250x250}}
{{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_20w/004.jpg?250x250}}
{{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_20w/005.jpg?250x250}}
{{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_20w/006.jpg?250x250}}
{{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_20w/007.jpg?250x250}}
{{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_20w/008.jpg?250x250}}
{{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_20w/009.jpg?250x250}}

===== 描述图 =====


===== 规格 =====




  主要应用：切割，金属雕刻，绘图深度雕刻等
  接口规格：4pin PH2.0（红：12V，黑：GND，黄：PWM，绿：温度信号）
  波长：450nm
  散热器尺寸：30*80mm
  材质：铜+铝
  重量：202g
  驱动位置:内置
  功率是否可调：可以PWM调节功率
  驱动保护功能：浪涌保护，过压保护
  输入功率：大约12V2A（不包含风扇功率）
  线长：300mm
  控制线安装方式：可插式
  风扇尺寸：30*10mm
  风扇转速：15000转
  可控温度：小于60摄氏度
  聚焦范围：5-50mm
  最佳焦距：距离出光口10mm
  安全警告：请在做好安全防护的前提下应用此模组！
  推荐应用机器：NEJE Master
  注意：NEJE Master标配12V2A充电器，如果您是希望升级旧款机器，需要另外准备一个12V3A电源
  包装清单：
   1 x 模组
   2 x 螺丝
   2 x 垫片
   1 x 控制线
   
--------------------------------

  Main applications: cutting, metal engraving, drawing depth engraving, etc.
  Interface specification: 4pin PH2.0 (red: 12V, black: GND, yellow: PWM, green: temperature signal)
  Wavelength: 450nm
  Radiator size: 30*80mm
  Material: copper + aluminum
  Weight: 202g
  Drive position: built-in
  Is the power adjustable: PWM can be adjusted
  Drive protection: surge protection, overvoltage protection
  Input power: approx. 12V2A (without fan power)
  Line length: 300mm
  Control line installation method: pluggable
  Fan size: 30*10mm
  Fan speed: 15000 rpm
  Controllable temperature: less than 60 degrees Celsius
  Focus range: 5-50mm
  Best focal length: 10mm from the light exit
  Safety Warning: Please apply this module under the premise of safety protection!
  Recommended application machine: NEJE Master
  Note: NEJE Master comes standard with 12V2A charger. If you want to upgrade your 
  old machine, you need to prepare another 12V3A power supply.
  packing list:
  1 x module
  2 x screw
  2 x gasket
  1 x control line