Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
ro:laser_module_405nm_3500u [2019/06/16 22:27] wuhonghe |
ro:laser_module_405nm_3500u [2019/06/25 23:28] wuhonghe |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_3500U/001.jpg}} | + | ===== 产品图 ===== |
- | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_3500U/002.jpg}} | + | |
- | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_3500U/003.jpg}} | + | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_3500U/001.jpg?250x250}} |
- | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_3500U/004.jpg}} | + | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_3500U/002.jpg?250x250}} |
- | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_3500U/005.jpg}} | + | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_3500U/003.jpg?250x250}} |
- | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_3500U/006.jpg}} | + | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_3500U/004.jpg?250x250}} |
+ | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_3500U/005.jpg?250x250}} | ||
+ | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_3500U/006.jpg?250x250}} | ||
+ | |||
+ | ===== 描述图 ===== | ||
+ | |||
+ | |||
+ | ===== 规格 ===== | ||
主要应用:灰度图雕刻,绘图,简单深度雕刻,简单切割等 | 主要应用:灰度图雕刻,绘图,简单深度雕刻,简单切割等 | ||
Line 17: | Line 24: | ||
输入功率:大约12V280ma(包含风扇功率) | 输入功率:大约12V280ma(包含风扇功率) | ||
线长:300mm | 线长:300mm | ||
- | 控制线安装方式:一体式 | + | 控制线安装方式:分体式 |
风扇尺寸:30*10mm | 风扇尺寸:30*10mm | ||
风扇转速:10000转 | 风扇转速:10000转 | ||
可控温度:小于60摄氏度 | 可控温度:小于60摄氏度 | ||
- | 聚焦范围:10-100mm | + | 聚焦范围:5-50mm |
- | 最佳焦距:距离出光口50mm | + | 最佳焦距:距离出光口10mm |
安全警告:请在做好安全防护的前提下应用此模组! | 安全警告:请在做好安全防护的前提下应用此模组! | ||
推荐应用机器:NEJE Master | 推荐应用机器:NEJE Master | ||
Line 29: | Line 36: | ||
2 x 螺丝 | 2 x 螺丝 | ||
2 x 垫片 | 2 x 垫片 | ||
+ | |||
+ | |||
+ | |||
+ | Main applications: grayscale engraving, drawing, simple depth engraving, simple cutting, etc. | ||
+ | Interface specification: 4pin PH2.0 (red: 12V, black: GND, yellow: PWM, green: temperature signal) | ||
+ | Wavelength: 405nm | ||
+ | Radiator size: 30*60mm | ||
+ | Material: copper + aluminum | ||
+ | Weight: 121g | ||
+ | Drive position: built-in | ||
+ | Is the power adjustable: PWM can be adjusted | ||
+ | Drive protection: surge protection, overvoltage protection | ||
+ | Input power: approx. 12V280ma (including fan power) | ||
+ | Line length: 300mm | ||
+ | Control line installation method: split type | ||
+ | Fan size: 30*10mm | ||
+ | Fan speed: 10,000 rpm | ||
+ | Controllable temperature: less than 60 degrees Celsius | ||
+ | Focus range: 5-50mm | ||
+ | Best focal length: 10mm from the light exit | ||
+ | Safety Warning: Please apply this module under the premise of safety protection! | ||
+ | Recommended application machine: NEJE Master | ||
+ | packing list: | ||
+ | 1 x module | ||
+ | 2 x screw | ||
+ | 2 x gasket | ||
| | ||