Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
ro:laser_module_450nm_7wu [2019/06/16 22:29] wuhonghe |
ro:laser_module_450nm_7wu [2019/06/16 23:21] wuhonghe |
||
---|---|---|---|
Line 6: | Line 6: | ||
{{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_7w/006.jpg}} | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_7w/006.jpg}} | ||
{{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_7w/007.jpg}} | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_7w/007.jpg}} | ||
+ | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_7w/008.jpg}} | ||
+ | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_7w/009.jpg}} | ||
+ | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_7w/010.jpg}} | ||
+ | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_7w/011.jpg}} | ||
+ | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_7w/012.jpg}} | ||
+ | | ||
主要应用:金属雕刻,深度雕刻,简单切割等 | 主要应用:金属雕刻,深度雕刻,简单切割等 | ||
- | 波长:450nm | + | 波长:450nm |
- | | + | |
散热器尺寸:30*60mm | 散热器尺寸:30*60mm | ||
材质:铜+铝 | 材质:铜+铝 | ||
- | 重量:116g | + | 重量:116g |
- | | + | |
接口规格:4pin PH2.0(红:12V,黑:GND,黄:PWM,绿:温度信号) | 接口规格:4pin PH2.0(红:12V,黑:GND,黄:PWM,绿:温度信号) | ||
驱动位置:内置 | 驱动位置:内置 | ||
功率是否可调:可以PWM调节功率 | 功率是否可调:可以PWM调节功率 | ||
驱动保护功能:浪涌保护,过压保护 | 驱动保护功能:浪涌保护,过压保护 | ||
- | 输入功率:大约12V750ma 不包含风扇功率 | + | 输入功率:大约12V750ma 不包含风扇功率 |
- | | + | |
线长:300mm | 线长:300mm | ||
- | 控制线安装方式:可插式 | + | 控制线安装方式:可插式 |
- | | + | |
风扇尺寸:30*10mm | 风扇尺寸:30*10mm | ||
风扇转速:10000转 | 风扇转速:10000转 | ||
- | 可控温度:小于60摄氏度 | + | 可控温度:小于60摄氏度 |
- | | + | |
聚焦范围:5-50mm | 聚焦范围:5-50mm | ||
- | 最佳焦距:距离出光口10mm | + | 最佳焦距:距离出光口10mm |
- | + | 安全警告:请在做好安全防护的前提下应用此模组! | |
- | 安全警告:请在做好安全防护的前提下应用此模组! | + | 推荐应用机器:NEJE Master |
- | + | ||
- | 推荐应用机器:NEJE Master | + | |
- | + | ||
包装清单: | 包装清单: | ||
1 x 模组 | 1 x 模组 | ||
Line 40: | Line 37: | ||
1 x 控制线 | 1 x 控制线 | ||
+ | ----------------------- | ||
+ | |||
+ | Main applications: metal engraving, deep engraving, simple cutting, etc. | ||
+ | Wavelength: 450nm | ||
+ | Radiator size: 30*60mm | ||
+ | Material: copper + aluminum | ||
+ | Weight: 116g | ||
+ | Interface specification: 4pin PH2.0 (red: 12V, black: GND, yellow: PWM, green: temperature signal) | ||
+ | Drive position: built-in | ||
+ | Is the power adjustable: PWM can be adjusted | ||
+ | Drive protection: surge protection, overvoltage protection | ||
+ | Input power: approx. 12V750ma does not include fan power | ||
+ | Line length: 300mm | ||
+ | Control line installation method: pluggable | ||
+ | Fan size: 30*10mm | ||
+ | Fan speed: 10,000 rpm | ||
+ | Controllable temperature: less than 60 degrees Celsius | ||
+ | Focus range: 5-50mm | ||
+ | Best focal length: 10mm from the light exit | ||
+ | Safety Warning: Please apply this module under the premise of safety protection! | ||
+ | Recommended application machine: NEJE Master | ||
+ | packing list: | ||
+ | 1 x module | ||
+ | 2 x screw | ||
+ | 2 x gasket | ||
+ | 1 x control line |