Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
laser_module_30603500u [2020/08/31 10:55] dav |
laser_module_30603500u [2022/03/18 11:53] dav |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ===== Control ===== | + | Compatible with master 2/2s 3, NEJE 2S/3 plus, NEJE 3 Pro, NEJE 2S/3 Max machines |
| - | note: | + | |
| - | 1. The third yellow interface line is the TTL control line, the voltage range is 3.3-12V, the frequency is 0-20KHz, and it needs to be grounded. | + | ===== Interface ===== |
| - | 2. The input voltage of the red and black wires is 12V1A, do not connect them in reverse, otherwise the module will be damaged. | + | {{https://nejetool.oss-us-west-1.aliyuncs.com/wiki/NEJE_3_Max/A40640_interface.png?300x300}} |
| - | 3. The power is not controlled by voltage or frequency, it is controlled by duty cycle. | + | 12V: Power positive . |
| - | **[[http://www.neje.club/download/20200612/How_to_get_laser_temperature.pdf|How_to_get_laser_temperature.pdf]]** | + | GND: Power ground or power negative. |
| - | {{https://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_7w/size1.png?250x250}} | + | TTL/PWM: TTL = PWM, input 3.3V~12V to turn on laser module, conect to GND to turn off laser module. |
| - | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_3500U/001.jpg?250x250}} | + | |
| - | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_3500U/002.jpg?250x250}} | + | |
| - | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_3500U/004.jpg?250x250}} | + | |
| - | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_3500U/005.jpg?250x250}} | + | |
| - | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_3500U/006.jpg?250x250}} | + | |
| + | Temperature: do not connect, please ignore. | ||
| + | |||
| + | Connect 12V and GND pin to 12V power, ensure the power adapter is sufficient, 5A is recommended. | ||
| + | |||
| + | Connect TTL/PWM pin to your control board PWM output pin. | ||
| - | Main applications: grayscale engraving, drawing, simple depth engraving, simple cutting, etc. | ||
| - | Interface specification: 4pin PH2.0 (red: 12V, black: GND, yellow: PWM, green: temperature signal) | ||
| - | Wavelength: 405nm | ||
| - | Radiator size: 30*60mm | ||
| - | Material: copper + aluminum | ||
| - | Weight: 121g | ||
| - | Drive position: built-in | ||
| - | Is the power adjustable: PWM can be adjusted | ||
| - | Drive protection: surge protection, overvoltage protection | ||
| - | Input power: approx. 12V280ma (including fan power) | ||
| - | Line length: 300mm | ||
| - | Control line installation method: split type | ||
| - | Fan size: 30*10mm | ||
| - | Fan speed: 10,000 rpm | ||
| - | Controllable temperature: less than 60 degrees Celsius | ||
| - | Focus range: 5-50mm | ||
| - | Best focal length: 10mm from the light exit | ||
| - | Safety Warning: Please apply this module under the premise of safety protection! | ||
| - | Recommended application machine: NEJE Master | ||
| - | packing list: | ||
| - | 1 x module | ||
| - | 2 x screw | ||
| - | 2 x gasket | ||