Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
laser_module_30607w [2019/12/30 12:14] wuhonghe |
laser_module_30607w [2022/03/18 11:53] (current) dav |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | Compatible with master 2/2s 3, NEJE 2S/3 plus, NEJE 3 Pro, NEJE 2S/3 Max machines | ||
| - | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_7w/001.jpg?250x250}} | + | ===== Interface ===== |
| - | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_7w/002.jpg?250x250}} | + | |
| - | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_7w/003.jpg?250x250}} | + | {{https://nejetool.oss-us-west-1.aliyuncs.com/wiki/NEJE_3_Max/A40640_interface.png?300x300}} |
| - | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_7w/004.jpg?250x250}} | + | |
| - | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_7w/006.jpg?250x250}} | + | 12V: Power positive . |
| - | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_7w/007.jpg?250x250}} | + | |
| - | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_7w/008.jpg?250x250}} | + | GND: Power ground or power negative. |
| - | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_7w/009.jpg?250x250}} | + | |
| - | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_7w/010.jpg?250x250}} | + | TTL/PWM: TTL = PWM, input 3.3V~12V to turn on laser module, conect to GND to turn off laser module. |
| - | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_7w/011.jpg?250x250}} | + | |
| - | {{http://nejetool.oss-us-west-1.aliyuncs.com/wiki/module_7w/012.jpg?250x250}} | + | Temperature: do not connect, please ignore. |
| + | |||
| + | Connect 12V and GND pin to 12V power, ensure the power adapter is sufficient, 5A is recommended. | ||
| + | |||
| + | Connect TTL/PWM pin to your control board PWM output pin. | ||
| - | Main applications: deep engraving, simple cutting, aluminum oxide etc. | ||
| - | Wavelength: 450nm | ||
| - | Radiator size: 30*60mm | ||
| - | Material: copper + aluminum | ||
| - | Weight: 116g | ||
| - | Interface specification: 4pin PH2.0 (red: 12V, black: GND, yellow: PWM, green: temperature signal) | ||
| - | Drive position: built-in | ||
| - | Is the power adjustable: PWM can be adjusted | ||
| - | Drive protection: surge protection, overvoltage protection | ||
| - | Input power: approx. 12V750ma does not include fan power | ||
| - | Line length: 300mm | ||
| - | Control line installation method: pluggable | ||
| - | Fan size: 30*10mm | ||
| - | Fan speed: 10,000 rpm | ||
| - | Controllable temperature: less than 60 degrees Celsius | ||
| - | Focus range: 5-50mm | ||
| - | Best focal length: 10mm from the light exit | ||
| - | Safety Warning: Please apply this module under the premise of safety protection! | ||
| - | Recommended application machine: NEJE Master | ||
| - | packing list: | ||
| - | 1 x module | ||
| - | 2 x screw | ||
| - | 2 x gasket | ||
| - | 1 x control line | ||